Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL GTX™ Resin GTX870 - Asia - (PPE+PA*)-GF20 - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL GTX™ Resin GTX870 - Asia:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Noryl GTX datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriedades mecânicas - Propriedades térmicas - Outras propriedades - Recomendação de processamento Moldagem por injeção
Any use of this information falls under the rules of our disclaimer.
Informação do produto
NORYL GTX870 resin is a 20% glass reinforced alloy of Polyphenylene Ether (PPE) + Polyamide (PA). This injection moldable grade exhibits high stiffness, excellent chemical resistance, and high heat resistance. NORYL GTX870 resin is an excellent candidate for a wide variety of applications including electrical connectors and electronic base stations.
Propriedades mecânicasValorUnidadeMétodo de ensaio
ASTM Dados
Resistência à tração no escoamento 122 MPa ASTM D 638
Deformação na ruptura 5 % ASTM D 638
Módulo de flexão 5680 MPa ASTM D 790
Resistência à flexão 166 MPa ASTM D 790
Impacto Izod com entalhe, 1/8 in 117 J/m ASTM D 256
Propriedades térmicasValorUnidadeMétodo de ensaio
ASTM Dados
DTUL @ 264 psi 200 °C ASTM D 648
Outras propriedadesValorUnidadeMétodo de ensaio
Absorção de água, 24hr 0.5 % ASTM D 570
Densidade 1240 kg/m³ ASTM D 792
Recomendação de processamento Moldagem por injeçãoValorUnidadeMétodo de ensaio
Pré-secagem - temperatura 95 - 105 °C -
Pré-secagem - tempo 3 - 4 h -
Umidade do processamento ≤0.07 % -
Temperatura da massa 280 - 305 °C -
Temperatura do molde 75 - 120 °C -
Zona 1 265 - 305 °C -
Zona 2 270 - 305 °C -
Zona 3 275 - 305 °C -
Temperatura do bico 280 - 305 °C -
Velocidade de parafuso 20 - 100 rpm -
Contrapressão 0.3 - 1.4 MPa -
Características
Processamento
Moldagem por injeção
Características especiais
Estável contra o calor
Resistência Química
Resistência química geral
Aplicaciones
Elétrica e Eletrônica
Disponibilidade regional
Ásia Pacífico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.